客服在线,欢迎咨询

您好,当前有客服在线,点击即可咨询

QQ交谈
电话咨询 售前咨询 扫码关注
  • 官方微信公众号

回到顶部

60W驱动电源调光调色WIFI蓝牙智能控制规格书

admin智能资料2021-12-17阅读(757)

全电压隔离反激式恒流驱动外置电源,带WIFI和蓝牙遥控器控制调光调色智能电源

 

60W驱动电源调光调色WIFI蓝牙智能控制规格书

60W驱动电源调光调色WIFI蓝牙智能控制规格书

Product Standard 产品规格

1Overview 概述

Power was developed by ADA Smart for LED lights, a full range of input voltage, isolated BUCK type constant current drive built-in power supply, this power supply USES the new circuit design, make the products with high power factor, high efficiency, high reliability, wide output voltage range, low noise, energy conservation, environmental protection, long life and other characteristics.With  WiFi/ bluetooth dimming and color adjustment function.

电源是阿达智能专为LED灯开发的一款全电压范围输入,隔离反激式恒流驱动外置电源电源采用全新的电路设计使产品具有高功率因素、高效率、高可靠性、宽范围电压输出、低噪音、节能环保、长寿命等特点带有WiFi/蓝牙调光调色功能。

2Applicable Scope适用范围

This product is suitable for the ball bubble lamp power supply, the output voltage is between 80120V LED lamps and lanterns.

本产品适用于家装备LED 输出电压介于DC80120VLED灯具。

3Electrical Parameters(电气参数)

Testing project

测试项目

Testing condition测试条件

Scope

范围

Unit 单位

Remark

备注

Input voltage range输入电压

220

AC175~265

V

 

Normal voltage range标称输入

220

AC175~240

V

 

Operating frequency工作频率

50Hz

47~63

Hz

 

Input current输入电流

Vin=AC220V

≤0.3

A

 

Input power输入功率

Vin=AC265V

≤63

W

 

Input Fuse 输入保险

2

A

 

Power factor功率因素

Vin=AC220V

≥96

%

/

/

/

%

Efficiency 效率

Vin=AC175V

≥94

%

Vin=AC220V

≥94

%

Harmonic current 谐波电流

Vin=AC220V

< 18

%

 

/

/

%

 

Output voltage输出电压

单路280mA

DC 80~120V

V

 

Output current输出电流

DC 80~120V

单路280

mA

±5%

Output power输出功率

AC 175~240

双路≤60

W

 

Short circuit power短路功耗

AC220

<1.5

W

 

.No-loadpower空载功耗

AC 220V

≤0.8

W

 

No-load voltage 空载电压

AC 220V

≤200

V

 

Ripple纹波

AC 220V

100

mV

/

Work mode工作模式

恒流模式

单路280

mA

±5%

Compression耐压

电源输入与输出

/

V

AC

Isolation绝缘性能

/

/

/

 

Ripple test matters needing attention(纹波测试注意事项):

1Measurements shall be made with an oscilloscope with 20MHz bandwidth.

   示波器须设置在20兆赫兹带宽。

2Outputs shall be bypassed at the connector with a 0.1uF ceramic capacitor and a 10uF

electrolytic capacitor to simulate system loading.

输出须并联0.1uF的陶瓷电容和10uF的电解电容来模拟负载。

4Rotective Value(保护性能)

4.1Open protection: when the output when open, input normal input, the product will not damage,

and open voltage can't more than ratings.

开路保护:当输出端开路时,输入端正常输入,产品不会损坏,且开路电压不会超过额定值。

4.2Short circuit protection: if the output appears unusual, causes the product of anode and short

sub, this product will start short circuit protection function, and not because this abnormality in

product permanent damage.

短路保护:如果输出端出现异常, 造成产品正负极短接, 本产品会启动短路保护功能, 不致因为此异常造成产品永久性损坏。

4.3Overload protection: this product is the constant flow design, the LED lights in the design of

t he product value VF voltage range, the product output current will be constant; When LED lamp

of the design of value over VF voltage range, the product will enter overload protection status.

过载保护:本产品为恒流设计,LED灯的VF值在产品的设计电压范围内时,此产品的输出电流会恒定不变;当LED灯的VF值超过所设计的电压范围时,产品会进入过载保护状态。

4.3.1Output voltage is too low, the power supply will enter frequent start and shut off, at this time

will frequently LED twinkle.

输出端电压过低,电源会进入频繁启动和关断,此时LED灯会频繁闪烁。

4.3.2The output voltage of the too high, this product into the constant pressure to protect state, this time the LED lights on the luminous intensity pronounced weakening, current is unable to achieve the ratings.

输出端电压过高,本产品进入恒压保护状态,此时LED灯的发光强度明显变弱,电流无法达到额定值。

5Dimension物理尺寸)

PCBA模组尺寸】长:210mm宽:24mm17mm

 

 

产品图片

60W驱动电源调光调色WIFI蓝牙智能控制规格书 

 

Environmental Requirement环境要求

This part describes the constant current drive power LED to use and storage environment.

这一部分描述了LED恒流驱动电源使用和存储环境。

1Using temperature and humidity使用温度和湿度

1.1Using temperature range: from 0 ℃ to 55 ℃

使用温度范围0℃55℃

1.2Use humidity range: from 5 RH % to 95 RH %

使用湿度范围:从5RH%95RH%  

2Storage temperature and humidity存储温度和湿度)

2.1Storage temperature range: from -20 ℃ to 80 ℃

存储温度范围:从-20℃80℃

存储湿度范围:从5RH%95RH%

 

三、Statement(声明)

1Pictures and specifications for reference only, pictures in kind prevail, specifications are subject to change, prior notice.

2The company products according to the delivery sealed samples shall prevail, if not sealed samples, we will press on a group of shipment inspection standard. Production of shipment.

3The company by the product of JianYanQi for five days, five days if there is no written puts forward problems bad, Our company as a qualified, the subsequent will enter the warranty period.

4Under the normal working Temp.& environment Continuous working time should be less than 2000H, the life time can be reached more than 5years.

1、图片与规格仅供参考,图片以实物为准,规格如有变化,另行通知。

2、本公司产品出货按双方封样为准,如未封样,我司将按上一批出货标准检测.生产出货。

3、本公司所出产品的检验期为5个工作日,5个工作日内如无书面提出不良问题,本公司视为合格,后续将进入保用期。

4、在正常工作和常温环境下,连续工作时间不超过2000小时,本产品的使用寿命累计可达5年或以上。

 

Product testing structure (产品测试结构图)

1Testing schematic diagram(测试原理图):

 

 

60W驱动电源调光调色WIFI蓝牙智能控制规格书

 

 

2Product interface diagram(接口图示):

This product has two connection port. 'AC-L' and 'AC-N' for product AC input terminals. Used to meet in AC AC input (input 100-265 V / 47Hz-63Hz alternating current) for another marked 'LED +' and 'LED-' ports used to pick up the lamps and lanterns of LED, specific the wiring diagram is as follows:

本产品有两个接线端口 “AC-L”与 “AC-N” 为产品的AC输入端子,用于接在交流AC输入端 (输入100 ~240V/47Hz~63Hz交流电);另为标有“LED+”与“LED-”的端口用于接LED的灯具。具体接线图如下:

60W驱动电源调光调色WIFI蓝牙智能控制规格书

3Product precautions产品使用注意事项):

3.1. In the device the power supply, please pay attention to the correct installation of input, output, confirms to the rear  can electrify.

3.2.In order to avoid LED burn out, please take good DC output terminal open again power supply.

3.3.In the use of the products please pay attention to high pressure safety, and completes the shock measures to avoid when installation and metal case short circuit, and don't force or throw the power on extrusion of components, or in the set of casing please don't use too much about the long time at a point in heating.

3.4.Power in the first time when a current good device, such as a bright lights or signal, please promptly ac power supply, and check input exchange or the output is bad contacts or overload or short circuit and remove the faults can, if there is a bright or dim light, please promptly ac power supply, and inspection of the parameters are needed to get LED anastomosis and remove the faults can.

3.5.Good electrical connections in the device, LED light but a flickering or WeiLiang, please check the power supply output terminal for contact undesirable or appears light load. Overload.

3.6.As in use process in time if you have any questions please contact with our company technical support, and feedback unhealthy phenomenon, my company will have professional technical staff of the service you.

3.1. 在装置电源时,请注意输入、 输出端的正确安装, 确认无误后方可通电。

3.2. 为了避免LED烧坏,请先接好DC输出端再开电源。

3.3. 在使用本产品时请注意高压安全, 并做好防电击措施, 安装时避免与金属外壳短路, 同时不要强行挤压或扳动本电源上的元器件,或在套套管时请不要用过高的风筒长时间在一个点上加温。

3.4. 电源在第一次装置好通电时,如出现灯不亮或灯闪时,请及时切断交流供电,并检查输入交流或输出端是否接触不良或过载或短路,排除故障即可,如出现灯过亮或暗淡时,请及时切断交流供电,并检验所接用的LED所需参数是否吻合,排除故障即可。

3.5. 在装置好电气连接后, LED灯亮但有闪烁或微亮,请检查电源输出端有无接触不良或出现轻载.过载。

3.6. 如在使用过程中如有疑问请及时与本公司技术支持联系,同时反馈不良现象,我公司将有专业的技术人员全程为您提供服务。

 

 阿达智能为LED灯开发的一款全电压范围输入,隔离反激式恒流驱动外置电源,全新电路设计,使产品具有高功率因素PF值、宽范围电压输出、低噪音、节能环保、长寿命等特点;带WiFi/蓝牙遥控器控制调光调色功能。2020年3月10日发布